bharatbhasha.com
Free Articles  >>  Home improvement >>  Page 874  >> 

REPLACING YOUR SLIDING GLASS DOOR ROLLERS





REPLACING YOUR SLIDING GLASS DOOR ROLLERS   by John Rocco


If the sliding glass doors in your home are more than 10 years old, you might notice that they are becoming harder to slide open. This problem is even more common on aluminum frame dual pane doors. The reason is because the doors are heavier due to the dual pane glass, but many of the aluminum units did not use stainless steel rollers. So, in many cases, the rollers get rusty from moisture and they start to bind.

In order to replace the rollers, you have to remove the sliding panel from the opening. In most instances, the fixed panel must be removed in order for the sliding panel to come out. There is a simple way to determine whether or not your fixed panel has to come out as well. If the slider is on the inside track and the fixed panel is on the outside track, you have to remove both panels, because the slider will only come out from the outside. There is a lip on the bottom of the track inside your house. That lip keeps water from coming in. Unfortunately, that lip is also too high to lift the sliding panel up and over. So, you have to remove the fixed panel first, then lift and swing out the slider from outside. If you are one of the few people who have a slider on the outside track, then you can lift your slider out without removing the fixed panel.

But, let's assume you need to remove the fixed panel first. Here is what you do: Remove your screen door if you have one. The screen door will have two rollers on the bottom. Lift one end of the door frame with one hand while using a flat screwdriver to lift the roller off the track. Do that on both sides, then take out the screen door and set it aside. Now, look for a metal piece on the bottom track that runs from the bottom corner of the fixed panel all the way across to the bottom of the side jamb that has the door lock hardware. If your door is really old that piece might be missing. If you have one, you can pry it up from the track. It is snapped in place even though it looks like it is a part of the track. Once you have that piece removed, you want to look inside the house where the fixed panel is against the wall jam. Look for screws holding the frame to the jam. They usually have one near the top and bottom corners, and one near the center. Remove these screws and put them where you won't lose them. Now, you should be able to pull the fixed panel out of the side jam. There is a very good chance that it will be stuck. If it is, grab the center rail near the bottom and lift up as hard as you can. If you feel the panel go up, pull it back down. Do this a couple of times, then try to pull it out of the side jam again. This usually loosens it enough to pull it out. If it still won't come out, you will have to put a thin screwdriver between the fixed panel frame and the side jam and pry while a helper pulls the panel away from the jam. Once you get it free of the side jam, grab the fixed panel side rail and have a helper grab the other rail. Lift the panel up into the top track and swing the bottom out of the bottom track. Remove the panel from the top track and set it aside with the screen door.

Now, you can try lifting the slider up and out, just like you did with the fixed panel. If the slider won't clear the bottom track, you need to do a couple of things. First, look to see if it's the old rollers protruding from the bottom that is preventing the door from coming out, or if the actual bottom of the door frame is hitting the track. In almost all cases, it will be the old rollers. But, if the opening is 8' wide, sometimes the wood header that runs across the opening has sagged just enough to make it tight in the center of the opening. If it's the rollers, you need to adjust them all the way up into the door. Look for a hole on the bottom side where you can put a phillips screwdriver and find the adjustment screw. Then turn that screw counterclockwise as far as you can. Do that to both sides, then try lifting out the door. If you are still getting stuck, have your helper lift one side and pull outward while you try to pry the frame and roller over the track. If you get one side out, have your helper hold that side with his or her foot to prevent it from going back in while he or she lifts the other side for you to pry free.

Once you get the slider out, almost all rollers are held in place by the same screw that holds the frame corners together. So, you need to set the panel on one side, remove the screw in the corner, flip the panel over, remove the screw on the other bottom corner. Now, you can take a rubber mallet or the wood handle of a hammer, and tap the bottom frame off the glass. This will give you access to your rollers. Take a close look at how they are inserted into the door frame. In fact, it's a good idea to only remove one roller to bring with you to match for the new ones. Then, when you get back home, you can use the roller that is still in place as a guide to installing the new ones.

Places like Home Depot, Lowes, and Ace Hardware carry about 80-90% of the rollers out there. So, you should be able to find them. However, let's say this just isn't your lucky day, and you can't find your rollers anywhere. You are going to have to have them ordered. Bring the roller to your local glass shop. If you're lucky, they will have them in stock. If not, they can order the rollers, but you won't get them for about a week. Don't panic. Just go home and tap the bottom frame back on the door panel, but leave the corner screws out. You can even leave the roller out that you removed. Lift the door back in place, install the fixed panel but don't snap the bottom piece back in, and don't install the inside screws. Then, from inside the house, lift the slider and pull it closed. You don't want to drag it if you left the roller out. It will scrape the bottom track. Just lift it enough to take the pressure off, and close and lock it.

When Your new rollers come in, take everything back out and install the new rollers. Adjust the new rollers all the way up before putting the door back in. That way, the new rollers won't interfere with you lifting it back in place. Adjust the new rollers down until the door slides good and locks. You want to be sure there is an equal gap at the top and bottom when the door is about an inch from closing into the side jam. You can adjust the rollers to make this dimension even. If you can get the job done by a professional for $50 or $60 including parts, it might be worth hiring someone to do it. But, in high population areas such as Los Angeles, it's common to pay $100 in labor only. Then they mark up the cost of the rollers, and you could wind up spending $130 for a job that you can do yourself for about $20. Next week i'm going to tell you how to repair your broken or defective window glass.


About Author John Rocco :

John Rocco has been installingreplacement windows since 1978.To learn more, visit <a href="http://www.how-to-install-windows.com">How To Install Windows</a>


Article Source: https://www.bharatbhasha.com
Article Url: https://www.bharatbhasha.com/home_improvement.php/27131

LD
Other Articles by John Rocco

INSTALLING VINYL REPLACEMENT WINDOWS ON THE SECOND FLOOR
by John Rocco I hope all of you had a nice Thanksgiving Holiday. Sometimes we get so busy in our lives that we forget how fortunate we all are to live in the greatest country on this earth. Those brave men and women in our armed forces make it possible, so keep them in your thoughts and prayers.If you have a two story house, and you are going to replace the windows on both the first and second floor, there are little tricks that you can use to make the upper floor job a bit safer and...

SLIDING GLASS DOOR REPLACEMENT
by John Rocco This article is going to be about replacing an old sliding glass door with a modern Vinyl frame sliding glass door. If you currently have french doors and you want to replace them with sliding doors, or vise versa, future articles will cover that topic.The first thing we have to do is measure for the replacement door. You want to measure across the bottom, center, and top of the existing door frame to find the narrowest dimension. Start outside and measure at the point where...

REMOVING OLD ALUMINUM WINDOWS
by John RoccoThis week we are going to talk about the process of actually removing your aluminum windows in preparation for installing vinyl replacement windows. Let's start with a horizontal sliding window, which is pretty common nationwide. There is going to be a sliding panel and a stationary panel. You want to remove the slider first. All you do is slide the panel open, grab the sides of the panel with your hands,lift up and swing out. Under ideal circumstances, it would be that easy....

REMOVING YOUR OLD SLIDING GLASS DOOR
by John Rocco Last week I explained how to measure your existing sliding glass door so you can order the vinyl replacement door. This week I am going to go over the steps required to remove the old sliding door before installing the new door.First, you have to remove the sliding panel and the stationary panel. The vast majority of doors out there have the sliding panel on the inside half of the track, and the stationary panel is on the outside. Whatever the case in your particular door, the...

Single pane Window glass repair in an aluminum frame
by John Rocco Happy new year everybody. I hope this is the year that you all find whatever it is that you are seeking in life. I really enjoyed seeing my family this holiday season, but two weeks is about all i can handle. I'm definitely glad to be back here in the beautiful Pacific Northwest.Let's suppose you still have those old aluminum single pane windows in your house,and one of the neighbor kids throws a ball through it. ( Your kid would never do that!) Depending on where you live in...

REPAIRING PUTTY WINDOW GLASS
by John RoccoHave you ever thought about fixing a broken window in your house, but didn't think you could do it because nobody ever taught you how to cut glass? Well, you really don't have to know how to cut glass in order to repair your window. If you knew how to remove the frame, you could order a replacement piece of glass from your local glass shop already cut to the proper size. Then, it's just a matter of installing the new glass into the frame. But, there are so many different kinds...

Single hung aluminum window glass repair
by John Rocco Let's talk about repairing broken glass in an aluminum frame single hung window. If it's the lower sash pane that is broken, it must be removed from the inside. You are going to have one of three different mechanisms that hold the lower sash up when you slide it open. If you can't see any mechanisms on the sides, then you have a block and tackle system consisting of a string and spring assembly. Find the thin metal clips in the side jambs just above the sash. Pull the bottom...

DUAL PANE WINDOW GLASS REPAIR
by John Rocco For the past few weeks, I have been explaining how to repair a broken window pane in your home. But, what if you have dual pane windows? Is the process the same? Well, pretty much, except for a couple of variations. So, let's review the single pane repair process, and I will point out the differences regarding dual pane windows. When we start talking about dual pane windows, one of the first things that comes to mind is vinyl window frames instead of aluminum. When dealing...

REPLACING ALUMINUM FRAME SINGLE PANE WINDOWS
by John Rocco In our past articles i talked about all the steps required to properly replace your old wood sash windows with energy efficient vinyl windows. I told you how to measure for the new windows. Then we discussed the removal of the wood sashes and parting bead. Finally, i told you how to install, seal, and trim the vinyl replacement windows. But, what if those old windows in your home are made of aluminum instead of wood? Is the process the same? No, it's not the same at all. So,...

Single pane glass repair in an aluminum frame part 2
by John Rocco This week we are going to continue our series on single pane window glass repair. Let's talk about broken glass in a fixed window, usually referred to as a picture window. The most common type will have metal stops on the outside, around all four edges of the window glass. Sometimes these stops will be held in place with screws, and other times there will be aluminum stops that snap in place. In some rare instances there will be a rubber material in place of metal. If you have...

Click here to see More Articles by John Rocco
Publishers / Webmasters
Article ID: 27131
DELINK URL from Authors Bio
REMOVE Article
Tell A Friend
Leave A Comment!
Download this article in PDF
Report Article!
Search through all the articles:


164 Users Online !
Related Articles:
Latest Articles:
 
home improvement >> Top 50 Articles on Home Improvement
Category - >
Advertising Advice Affiliate Programs Automobiles
Be Your Own Mentor Careers Communication Consumers
CopyWriting Crime Domain Names DoT com Entrepreneur Corner
Ebooks Ecommerce Education Email
Entertainment Environment Family Finance And Business
Food & Drink Gardening Health & Fitness Hobbies
Home Business Home Improvement Humour House Holds
Internet And Computers Kiddos and Teens Legal Matters Mail Order
Management Marketing Marriage MetaPhysical
Motivational MultiMedia Multi Level Marketing NewsLetters
Pets Psychology Religion Parenting
Politics Sales Science Search Engine Optimization
Site Promotion Sports Technology Travel
Web Development Web Hosting WeightLoss Women's Corner
Writing Miscellaneous Articles Real Estate Arts And Crafts
Aging


Disclaimer: The information presented and opinions expressed in the articles are those of the authors
and do not necessarily represent the views of bharatbhasha.com and/or its owners.


Copyright AwareINDIA. All rights reserved || Privacy Policy || Terms Of Use || Author Guidelines || Free Articles
FAQs Link To Us || Submit An Article || Free Downloads|| Contact Us || Site Map  || Advertise with Us ||
Click here for Special webhosting packages for visitors of this website only!
Vastu Shastra

Personal eMail Provided By AwareIndia







Company IDS