bharatbhasha.com
Free Articles  >>  Business And Finance >>  Page 3926  >> 

How To Make Money Making Magnetic Signs





<p align="Justify">How To Make Money Making Magnetic Signs

Making magnetic signs in your garage or shop not only profitable -- it can be fun! Magnetic signs are vacuum formed, 3-D sheets of plastic with two-way foam or magnetic strips on the back to hold them in place.

The "book" on magnetic signs has not yet been finished because each every new entrepreneur discovers new innovations, such as "cast iron" finish or metallic paints and relief cameos. The primary products, magnetic car and truck signs, are widely accepted but there is still plenty of room for your creative talents!

The initial investment to go into this business is approximately $1,000 for some basic no-frills equipment and startup supplies. The cost of making a pair of 12 x 24 inch (the standard size) is about $7.00 with 10 -15 minutes labor. A pair this size sells for about $40 ($24 wholesale).

The magnetic sign process is performed by placing a 28 by 16 inch start white vinyl plastic into a vacuum machine, heating the plastic until it softens, then "pulling" it down over an arrangement of letters with a vacuum pump.

The vacuum machine looks something like a suitcase -- with heating wires in the top perforated baffle about 4 inches below the rim of the bottom. The vacuum motor is underneath the baffle and the controls are on the outside front. The plastic is laid across the bottom half and sealed when the lid is closed.

The heat is turned on a couple of minutes (until the plastic begins to sag), then it is turned off and the seconds, during which time the plastic is pulled down onto the perforated baffle.

When the vacuum machine is opened, the resulting sign has a raised impression of whatever design was placed on top of the baffle. The rough sign is then removed, trimmed, magnetic tape applied, and the raised portions are "painted" with rubber rollers (brayers) and vinyl "ink" (Paint). Minor errors are scraped off with pocket knife and PRESTO, a finished magnetic sign!

The magnetic sign "art" is fashioning and arranging the models (letters, logos, etc.) that create the sign. Letters and logos are about 1/8" thick (thicker for large items). They are arranged or laid out exactly as the sign should appear.

A wide variety of letters (sold in sets or "fonts"), Logos and various special effects such as borders, corner embellishment and arrows are available commercially in magnetic, metal or composition material.

Magnetic are the most expensive and are used for designs laid out directly on the baffle. Their magnetism helps them stay in place as the hot plastic forms over them. Metal letters are also expensive, but long lasting. Composition letters are used for the clipboard process (see below), and are quite easy to make yourself.

There are two basic methods of laying out copy. The first (and fastest) is to arrange magnetic letters directly onto the baffle and "pull" the sign down over them. This method, however, often results in slippage -- letters on the outside are moved slightly as the plastic catches them in the pulling process. It also is difficult to keep everything "together" for more than a couple of pulls.

Other drawback are the cost of magnetic letters, that only the old, two-way cellophane back magnetic tape can be used (foam backed would melt) and, that the baffle holes show through onto the sign (although few customers seem to mind).

The other, (chipboard) method involves gluing magnetic OR ANY OTHER TYPE LETTER or design onto pieces of chipboard that are the exact size of the desired sign.

Chipboard is a gray composition material like that found on the back of writing tablets -- its is porous enough to let the vacuum process work, and smooth enough to give the sign a nice, satin finish.

Most sign operators have many different styles of chipboard patterns -- all cut to shape, with rounded corners even custom shapes. Lines are drawn on them with FELT TIPPED PENS ball point leaves lines that show on the sign!) as layout guides.

Some even have circular lines so the letters of top line of the sign can be laid out in an arch. As the letters are placed onto the chipboard pattern, a touch of glue is added (white, or gluestick), to hold them in place (use more glue for more impressions). Once the sign is laid out, place the whole thing in the machine and make as many signs as you need.

When finished, pick off the letters and use a piece of sandpaper to smooth the remaining glue on the chipboard. Occasionally, you may have to wash the letters -- but not often.

Chipboard signs do not show the tape lines because the tape is applied after the sign has been formed. They are especially desirable in cases where several sets are needed -- and for those little space-fillers, because the letters stay in place. They also offer the advantage of custom shapes. Any shape you can cut out of the chipbaord can be the shape of your sign, which can be used over and over again (thanks to the sandpaper technique).

Finally, the chipbaord sign is now every bit as durable, due to the advent of foam backed magnetic tape.

Several years ago there were problems with the magnetic tape coming off, even for signs molded in the machine (where the tape and plastic are hot when they "meet").

This problem was sometimes caused by improper molding or the use of mold release spray in the area. The proper way is to frame the desired sign on the baffle with the magnetic tape, then pull off the protective cover at the last moment before the sign is pulled. Signs made this way show both the baffle holes and the magnetic tape impression.

Signs not made this way (e.g.,chipboard) should ALWAYS have foam backed magnetic strips or full magnetic backs. Otherwise, there will be detachment problems.

Full magnetic back material costs about twice as much as strips and is half as thick. It does make a nice, sturdy sign, but probably won't last any longer or perform any better!

Some sign makers use styrene plastic sheets, which are much cheaper than vinyl (or clear butyl) -- but they will not last outside. Styrene should be use for experimentation, molding and inside signs only. It is wise to keep a few sheets around for these purposes.

Note that styrene will not stick to vinyl and vice versa. Styrene works fine for molding and will keep for months if kept flat and out of the sun. Many sign makers keep impressions in styrene in case they need to mold more letters or logos.

There are several ways to mold your own letters and logos. You can mold from impressions you make, or copy one from another sign (clean the back and spray it lightly with mold release first).

Although you can use temporary material, such as fiber glass, most of these will not hold up in the vacuum machine for more than one or two pulls (due to the heat), and some will require lots of mold release (or baby powder).

Molding compound (two part) is expensive, but yields very inexpensive fonts. If you want to save money, buy a font of PLASTIC letters, make an impression of them in styrene, then mold your own letters with a good quality molding compound. You will be able to save about 85%!

Another way to save money is to make your own models out of Masonite or chipboard (two ply). You can make arrows, lines, flowers, whatever (#8 copper wire makes excellent parentheses; model airplane balsa strips are great lines and boxes).

If you want more copies, make an impression in styrene -- or unused portion of a sign that you are pulling -- and mold as many as you need.

Selling magnetic signs is a matter of getting out the word. If you want to wholesale, take a few (small) samples around and call on stationery stores. Tell them about your service and how long it will take to get a pair of signs they order (since you are local, you can beat out-of-towners).

When they agree to take orders, leave a price list and your phone number. If you also retail, you must sell at the same "suggested" retail prices (or your accounts will leave you flat). Put signs on your truck or car (sides and back), a small ad in the paper, and have a few cards printed.

Set up a record-keeping system, get some sales books from the dime store (stamp them with your company name), and start cranking out signs.

Although anyone can learn to make magnetic signs, the best advice is to get an outfit, invest in some styrene and an 8 oz bottle of styrene paint, and "ruin some plastic."

It takes a little practice to become proficient at spacing letters and painting the rollers, etc. but you will catch on surprisingly fast.

An easy way to keep track of orders that come in by phone (usually from retail accounts) is to keep a bound notebook next to the phone, and make a little box beside each order.

List the date, account and full details of the sign ordered. When the order is finished and delivered check off the little box -- this will let you see at a glance which orders are still pending at any one time.

The biggest potential problem area is that you might make mistakes that result in lost time and money.

Make sure all of your "copy" is written down and keep a dictionary handy. When taking orders by phone, be especially careful to get the correct message, spelling, colors, etc.

When laying out the work, pin the order at eye level above where you are working -- and double check the sign against the order before putting your finished layout into the machine... If there is the SLIGHTEST doubt in spelling or wording, check before you pull!

One other thing be aware of is the size of your vacuum machine. The standard sign is 12 x 24", so your machine should be big enough to make one OR TWO signs at a time. With odd sized machines, you may have a lot of expensive waste.

Tip: If you consider buying a second machine, get one that will use the same size rolls of plastic, so you can buy in bulk and use the same cutting boards, etc.

You can also make customized plates in a standard vacuum machine ( 3 at a time in a 12 x 24 inch model). This simply requires three chipboard patterns upon which you lay out and glue the desired copy. And, you can make impressions of almost anything.

One sign maker glued bolt heads on his chip board and painted them so the sign look like they are bolted on the vehicle! Another trick is to cover the chipboard with fabric (use 3-M spray adhesive for this) for an interesting background. There are thousand of other variations that you will discover in this fascinating business.

Note also that once you are in the magnetic sign business, the same customer will be interested in printing, engraved signs, and all sorts of things that are associated with starting and promoting small businesses.

Tips: to make "metallic" paint, add an ounce of aluminum to seven ounces of regular color. For a cast iron appearance, form over sandpaper, paint black and apply metallic rub 'n buff.

BUSINESS SOURCES

EL DO PLASTICS, INC., 451 El Dorado, AR 71730, 800/643-1556. Magnetic sign equipment and supplies; logos, letters fonts, engraving equipment, self-stick letters. Holds annual spring seminars (highly recommended!). Very reliable.

NATIONAL BANNER CO.,11938 Harry Hines Blvd.,Dallas, TX 75234. Flags, pennants, custom printed and standard banners, etc. Reliable.

JOHNSON PLASTICS, 10809 Normandale Blvd.,Minneapolis, MN 55437, 800/328-3778. Magnetic sign, engraving equipment and supplies (has styrene plastic sheets). Very reliable.

STOP-LOOK SIGN CO. Box 20447, Los Angeles, CA 90006, 800/447-4467. Stock signs, specializing in reader boards and large (18 x 24" open/closed signs).

THE REFLECTORY, box 1031, Newburg, FL 33685. Reflective stickers and decals.

CREATIVE PLASTICS, Box 260635, Tampa, FL 33685, 800/885-4257. Plastic letters, frames and plates for font license plates. Has the small plastic letters, logos, zodiac signs, etc., that can be molded and copied.

FRANZ SIGN CO., 8 Glover St.,Portsmouth, OH 45662. Stock signs.

THE TRENBIE CO.,8044 W. 3rd St.,Los Angeles, CA 90048, 213/655-9635. Wholesales sets of reusable static-hold letters for store windows.

BUMPA-TEL, INC.,P.O. Drawer A, Cape Girardeau, MO 63701, 800/334-2211. Magnetic sheeting for full-back magnetic signs. Excellent prices.

THE KELSEY CO.,P.O. Box 941, Meriden, CT 06450. 203/235-1695. Art, printing and craft supplies. Old reliable company that has things many suppliers no longer carry. Free catalog.

DICK BLICK CO.,P.O. Box 1267, Galesburg, IL 61047-1267. 800/677-8192. Art supplies including paints that work on magnetic signs. Write for catalog.

DOVER PUBLICATIONS, INC.,31 East 2nd St.,Mineola, NY 11051. 516/294-7000. Discount books, clip art, stencils, etc.

QUILL CORPORATION, 100 Schelter Rd.,Lincolnshire, IL 60917-4700, 312/634-4800. Office supplies.

IVEY PRINTING, Box 761, Meridan, TX 76665. Letterhead: 400 sheets plus 200 envelopes - $18.

SWEDCO, Box 29, Mooresville, NC 28115. 3 line rubber stamps - $3; business cards - $13 per thousand.

ZPS, Box 581, Libertyville, IL 60048-2556. Business cards (raised print - $11.50 per K) and letterhead stationery. Will print your copy ready logo or design, even whole card.

WALTER DRAKE, 4119 Drake Bldg.,Colorado Springs, CO 80940. Short run business cards, stationery, etc. Good quality, but no choice of style or color.
This Article is Courtesy of <a target="_blank" href="http://www.MalaMaal.com"> http://www.MalaMaal.com</a> - the ultimate Resource for <a target="_blank" href="http://www.malamaal.com/">Instant Download eBooks and Software</a> covering various subjects that include health, self-improvement, diet and weight loss, recipes, love and relationships, Christianity, blogging, RSS, sales and marketing, scripts and templates, search engine optimization, traffic building, etc. You are free to reprint this article in other websites, as it is without editing, as long as the author's biography and all active hyperlinks (including anchor text) remain intact.
About Author MalaMaal.com :

<a target="_blank" href="http://www.malamaal.com/">MalaMaal.com</a> is a unique eStore with the Latest Collection of <a target="_blank" href="http://www.MalaMaal.com/">Resell Rights eBooks and Software</a>. Most of these eProducts are sold at fabulous discounts, some at over 90% Off on their list prices. Free eBooks are also available for instant download.


Article Source: https://www.bharatbhasha.com
Article Url: https://www.bharatbhasha.com/finance-and-business.php/32587

LD
Other Articles by MalaMaal.com

How To Start Your Own Sign Distribution Business
How To Start Your Own Sign Distribution Business A potentially profitable business that can be operated from the home is a retail and/or wholesale sign route.Every business needs signs -- from the OPEN/CLOSED and HOURS OF OPERATION on the doors to the flashing arrow or neon sign outside. No merchant can afford to operate a retail establishment these days without signs.Many of the signs small businesses have, especially those on main streets and highways were purchased from route salesmen, or...

Starting A Silk Screening Business Inexpensively
Starting A Silk Screening Business Inexpensively Silk screen or screen printing (technically, Serigraphy) is a long used process for mass producing signs and designs economically.Going into this business may require a little more time (to learn), effort (to set up) and money (equipment and supplies) than some, but it is a business that could virtually explode into something REALLY BIG!The basic idea in silk screening is to create a master screen through which paint can form designs on a large...

Make Big Money In Your Own Bumper Sticker Business
Make Big Money In Your Own Bumper Sticker Business Bumper sticker sales can be a lucrative source of income for one who is willing to learn good selling techniques, anticipate customer needs and plan ahead.One company sells bumper stickers kits -- a few strips of adhesive paper, some magnetic letters and a couple cans of black fats-dry spray paint.The blank bumper sticker paper is placed on a metal surface and magnetic (to keep them from slipping ) letters arranged to spell out the...

Big Profits In The Sign Fabrication Business
Big Profits In The Sign Fabrication Business A few years ago it would have been foolish to even consider a sign business unless you were well qualified to hand paint letters and illustrations.But the modern age is upon us: the sign business is no longer confined to those with special artistic talent. Although it would be helpful to be able to paint your own signs, it is certainly not necessary. Some very expensive franchise today involve little more that a computerized machine that cuts out...

How To Make Extra Money With A Delivery Service
How To Make Extra Money With A Delivery Service If you have a truck, motorbike, van or even a small trailer, you can use it to deliver messages or make light deliveries. Contract with stores and businesses to deliver their messages and or packages on a retainer plus trip basis, such as $50 per month or year retainer and $4 per delivery (within the city) or 20 cents per mile.DELIVERY SERVICEMany businesses either have a need to deliver or have customers who need delivery service.Examples are...

Auto Dealer s Tips For Choosing The Best Used Car
44 Auto Dealer's Tips For Choosing The Best Used Car1. Examine the car's exterior thoroughly. Look for rust, dents and evidence that portions of the car have rusted out and been repaired with body putty. 2. Look under car for breaks in the frame and signs that frame has been welded. 3. Check for excessive rusting of frame. 4. Examine condition of muffler, tailpipe and exhaust pipe. 5. Look for signs of oil or transmission fluid leakage under the car. 6. Check for signs of...

Making Money And Friends In The Handyman Business
Making Money And Friends In The Handyman Business There are a lot of people today who just can't take care of all those little things around the house and yard that need to be done. Painting the cabinets, fixing a leaky faucet, installing a new plus on the lamp cord or replacing a screen can be real problems to some people.And, unless you have in a cave for the past few years, you know how much it can cost to call in a plumber, and electrician or carpenter these days.A Handyman Business...

Directory Of Service Business Opportunities
Directory Of Service Business Opportunities Write to these companies for more information on the business opportunities they have available.ANNOUNCEMENT SERVICES ----- CradleGram Inc., PO Box 16-4135, Miami, FL 33116 Do-It-Yourself Party Yard Signs, 709 W. Mulberry Dr., West Bend, WI 53095 Main Event Lawn Signs Inc., 911 E. Brookwood Dr., Arlington Heights, IL 60004 Rent-A-Stork, PO Box 12302, Portland, OR 97212 Stork On The Run, 1206 Bayview Ave., Shady Side, MD 20764 Stork's...

How To Avoid Traffic Tickets
How To Avoid Traffic Tickets Make every effort to know and comply with basic traffic laws. Get a copy of the driver's license manual from your state licensing authority and review its contents.Don't attract attention to your vehicle by having loud exhaust, windows tinted too dark, etc. Anything that causes a police officer to look at your vehicle will make it more likely he will notice expired tags or inspection sticker, or other deficiency.If your state has a mandatory seatbelt law; wear...

Tweaking Every Last Penny Out Of Your Garage Sale
Tweaking Every Last Penny Out Of Your Garage Sale Garage sales are like any other form of business. To get the most money out of your garage sale, you have to know what you are doing. You have to be acquainted with the market, advertise for business, offer competitive prices and quality merchandise.The first thing to do in most cases, is visit or check with your local municipal government about the laws surrounding garage sales. You may be required to purchase a license to legally hold your...

Click here to see More Articles by MalaMaal.com
Publishers / Webmasters
Article ID: 32587
DELINK URL from Authors Bio
REMOVE Article
Tell A Friend
Leave A Comment!
Download this article in PDF
Report Article!
Search through all the articles:


162 Users Online!!
Related Articles:
Latest Articles:
 
Business And Finance >> Top 50 Articles on Business And Finance
Category - >
Advertising Advice Affiliate Programs Automobiles
Be Your Own Mentor Careers Communication Consumers
CopyWriting Crime Domain Names DoT com Entrepreneur Corner
Ebooks Ecommerce Education Email
Entertainment Environment Family Finance And Business
Food & Drink Gardening Health & Fitness Hobbies
Home Business Home Improvement Humour House Holds
Internet And Computers Kiddos and Teens Legal Matters Mail Order
Management Marketing Marriage MetaPhysical
Motivational MultiMedia Multi Level Marketing NewsLetters
Pets Psychology Religion Parenting
Politics Sales Science Search Engine Optimization
Site Promotion Sports Technology Travel
Web Development Web Hosting WeightLoss Women's Corner
Writing Miscellaneous Articles Real Estate Arts And Crafts
Aging


Disclaimer: The information presented and opinions expressed in the articles are those of the authors
and do not necessarily represent the views of bharatbhasha.com and/or its owners.


Copyright AwareINDIA. All rights reserved || Privacy Policy || Terms Of Use || Author Guidelines || Free Articles
FAQs Link To Us || Submit An Article || Free Downloads|| Contact Us || Site Map  || Advertise with Us ||
Click here for Special webhosting packages for visitors of this website only!
Vastu Shastra

Linux Web Hosting Provided By AwareIndia







Company IDS