bharatbhasha.com
Free Articles  >>  Arts And Crafts >>  Page 119  >> 

Wood Carving How to Sharpen Straight Chisels





If youíre just starting out as a wood carver, youíll quickly discover how wood chisels are used all the time. There are many kinds, many sizes. Theyíll need periodic sharpening and itís good to be able to do them yourself. It isnít very fitting to have to bring your tools to a professional sharpener whenever they become dull. You lose money, you lose time. And best of all, straight chisels are the easiest wood carving tools to sharpen.

Straight chisels can be sharpened in two steps. The first is to get the tool's edge to sharpness, and the second is to strop that edge to silky smoothness.

◦ Straight Chisel Sharpening. This is sharpening for straight square chisels and it's very simple. Start with a coarse grade sharpening (honing or whetting) stone. Make the shaft vertical with the edge touching the stone. Slowly lower the end facing up until the edge's surface touches the wood. Stop right there. With the beveled face flush on the stone, you have achieved the correct sharpening angle.

While holding the chisel's beveled face flush against the stone, place your index finger on the top of the beveled surface for better control. Pull the stone towards you, away from the edge. Do this 10-20 times and then check for the burr. A burr is a feather-like sliver of wire that will come off the chisel's edge when you have achieved absolute sharpness. You slide your finger across the edge (never lengthwise!) and a burr will feel like sand or grit on your edge. If there isn't a burr, do another set of strokes until you've correctly raised it. If the tool has a second bevel, sharpen it as you have just done with the first bevel. Sharpen until you've correctly raised the burr.

After sharpness has been achieved with a coarse stone, move to a fine grade stone. You can do this with just one fine grade stone or with a succession of increasingly fine grade stones. Perform the sharpening strokes in the same way until you get a burr. If you've got a second bevel, do the same until a burr is raised. Be very sure that you've raised a burr along the entire length of the chisel's edge, and on both sides. If you won't make sure, just stop what you're doing and go watch television. I'm not kidding. If you're going to sharpen, do it well or not at all. It will affect how well you're able to carve. (If that doesn't matter to you, really, then what are you doing?)

There are a couple of different stroke techniques that are commonly used when sharpening straight chisels. With your index finger on the top of the beveled surface as you grip the shaft, place the fingers of your other hand on top of the first. Instead of pulling the tool towards you, you run it in circles. If not that, you can also push the tool sideways in one direction and then sideways in the other. There is no one specific method. Experiment and see which technique is best for you. I like the stroke that pulls away from the edge best. It's the simplest way to raise a burr and then detect it.

◦ Skewed Chisel Sharpening. Skewed chisels are just a bit different from straight chisels. A skewed chisel's edge is at a slanted angle, a skewed angle, and joins the side of the chisel head at an acute angle of less than 90 degrees.

Sharpening a skewed chisel is done in just the same way as sharpening a straight chisel. There is only one difference. The skewed edge needs to be made parallel to the forward edge of the sharpening stone. Or the edge can be made perpendicular to the side edge of the sharpening stone. Either way works fine. Just be consistent if there is a second bevel.

◦ Chisel Stropping. Your well-sharpened chisel now has burrs all along its edge. Well done. Stropping will remove those burrs and all other micro-bits still clinging.

You've got a couple of choices when it comes to stropping. First choice: You can use a free strap of leather to strop your edge in one direction and then the other. Lay the beveled face of your chisel's edge flat on the strap and pull away from the edge, parallel to the length-wise surface of the strap. Near the end of the strap, lift the chisel and turn it over. Place the opposite face of the chisel's edge flat on the strap. Pull in the opposite direction, away from the edge and parallel to the strap surface. Back and forth and back and forth until your edge is silky smooth.

The second choice for stropping your chisel edge is to use a stropping board, also referred to as a honing board. This could be in the form of a flat rectangular board, a paddle, a wooden bench or it could be one you make yourself. The technique for using a stropping board is just the same as the technique used on a free leather strap.

Leather strops and stropping boards are usually combined with a polishing compound. It facilitates the stropping process and makes carving much easier. It may be in the form of a liquid, a paste, a powder or even a solid block that fits in the palm of your hand.

Stropping is a very important step in sharpening and shouldnít be dismissed. Think of it as you using a chisel with a dirty edge. It surely doesnít perform as well as a clean edge. And because itís dirty, using it will cause you to have to sharpen it much quicker than you usually would. So strop, and strop well. Your carving will be better for it.

Beginners need to be very careful when stropping. As novices in this art, the edge is often rounded instead of being polished smooth. That's because the edge isn't truly flat during the stropping process. A secondary bevel will be produced that thickens with each sharpening. Eventually, the only way to save the edge is to remake it. That would be a great loss in time and effort. Pay close attention.

When youíve trained those hands to do a good job, youíll be able to sharpen any straight chisel, any skewed chisel in your tool collection. Thatís a lot you already know about sharpening carving tools. Keep it up. Just be so careful and watch out for secondary bevels.
About Author Len Q. :

Len Q. is a master blade sharpener.  If you would like to find out about ª  Knife Sharpening:  How to Sharpen Knives, Maintain and Store Them    ª  Sharpening Other Edges (i.e. Chain Saws, Lawn Mower Blades, Gardening Tools, Axes)Find it at http://www.MakeKnivesSharp.com 


Article Source: http://www.bharatbhasha.com
Article Url: http://www.bharatbhasha.com/arts-and-crafts.php/100500


Article Added on Wednesday, October 15, 2008
LD
Other Articles by Len Q.

Wood Carving How to Choose the Right Tools
If youíre going to be a wood carver and not just a whittler, youíll need to select a number of tools. Thereís just no way around it. So what are the right tools for wood carving? Tools for Sharpening. Before the carving tools, it seems appropriate that tools for sharpening them should come first. After all, first we sharpen and then we carve. At the very minimum, you should have a sharpening stone and a strop. The sharpening stone is used to get your edges to sharpness. Many sharpening stones...

Whittling Whittling Vs Wood Carving
Whittling is the removal of pare shavings or the cutting of small bits from a piece of wood using a knife or similar wedge-edged tool. It is the most basic form of wood carving but it is not actually the art of wood carving, as it is done today. Wood carving requires a number of tools, even power tools at that. So it could get complicated pretty fast. But this is not how it is when one whittles. All you need to whittle are two things: a piece of wood and a knife. True whittling has always been...

Wood Carving Bevels and Cutting Angles
Most wood carving tools are cutting tools. Every cutting tool has at least one bevel. This is the sloping surface coming off the edge. But itís more than jut a sloping surface. Itís actually a cutting angle. So the bevel supports a specific cutting angle that determines how the tool can be used. Experienced carvers know about bevels and how they affect cutting efficiency. If youíre just starting out as a wood carver, and youíre going to purchase carving tools for the first time, here are some...

Wood Carving So You Want to Be a Wood Carver
Wood carving is a special craft. It requires extreme patience that could flourish with a fine imagination. If you decide to become a wood carver, youíll have several styles to choose from. You could use just a piece of wood and a small knife. Or you could go so far as using power tools. So how can you know which style is best for you? There are five main styles of woodcarving. Each style is distinctly different from the other. These styles are whittling, chip carving, relief carving, intaglio...

Whittling So You Want to Whittle Wood
Whittling has been around for many hundreds of years. All the way back to the days of cavemen. One could say that it is because we began to whittle that technology began. It was the shaping of wood, after allóafter the discovery of sharp edgesóthat sparked human imagination to make carts, cooking implements and clothes, weapons for hunting and methods of food gathering. Who wouldíve thought? So you want to whittle wood. Good for you. Whittling is the simple removal of pare shavings or cutting...

File Sharpening For Your Yard
When itís time to clean up outside and do the yard, certain tools are commonly used no matter where you are. But Iím not talking about gardens and gardening tools. Iím talking about the yard itself. If youíve got a lawn, youíll probably own a lawn mower. If you have trees in your yard, you may have a chain saw, even an axe. Whatís your plan when your blades become dull? When the lawn looks unhealthy after youíve just cut it, when your chain saw is taking too long to do its job, when youíre...

Carving Pumpkins Jack O Lanterns Of The Twenty First Century
Every year at Halloween, jack-o-lanterns are everywhere. On doorsteps, on window sills, hanging as paper on walls, even as plastic candy collectors for trick-or-treaters. You can easily find them in department stores, restaurants and even along public streets. They are an absolute part of Halloween. Many things have changed over the hundreds of years since jack-o-lanterns were first brought to America. The pumpkin is no longer always a real pumpkin. As a matter of fact, artificial...

Wood Carving How To Make A Gouge Honing Board
Once a gouge has been correctly sharpened, it doesnít take much afterwards to bring the edge back to absolute sharpness. This refers to the natural wearing away of the edge from use and not as a result of it being damaged. When all it needs is some honing, a bringing back to razor-sharpness, and not a true sharpening, thereís something very handy that you can do about that. One way to bring your edge back to pristine condition is to make a gouge honing board. Instead of using a fine grade...

Knife Sharpening Experts Electric Knife Sharpening
If youíre a person who has many knives, many edges to sharpen at a fairly consistent pace, electric knife sharpening is for you. So much time and effort will be saved. But take heed. Using these devices without proper training and only a little experience could be a regrettable move. Electric knife sharpeners are well known for producing great heat while sharpening. Friction from the metal edge against the sharpener over time will do that. Youíve got to know just how hot youíll allow the metal...

Carving Pumpkins How to Carve a Traditional Jack O Lantern
Would you believe that Halloween has been celebrated for over two hundred years? Would you believe that it was celebrated for much longer than that in Ireland? Yes, itís true. This wonderful tradition originated on shores far, far away. And wouldnít you know it, but Ireland didnít even have pumpkins back then. Really. They used carved out beets or turnips for lanterns. When Irish families came to America and discovered the gigantic pumpkin, they marveled at its size and at how easy it was to...

Click here to see More Articles by Len Q.
Publishers / Webmasters
Article ID: 100500
DELINK URL from Authors Bio
REMOVE Article
Tell A Friend
Leave A Comment!
Download this article in PDF
Report Article!
Search through all the articles:


117 Users Online!!
Related Articles:
Latest Articles:
 
Arts And Crafts >> Top 50 Articles on Arts And Crafts
Category - >
Advertising Advice Affiliate Programs Automobiles
Be Your Own Mentor Careers Communication Consumers
CopyWriting Crime Domain Names DoT com Entrepreneur Corner
Ebooks Ecommerce Education Email
Entertainment Environment Family Finance And Business
Food & Drink Gardening Health & Fitness Hobbies
Home Business Home Improvement Humour House Holds
Internet And Computers Kiddos and Teens Legal Matters Mail Order
Management Marketing Marriage MetaPhysical
Motivational MultiMedia Multi Level Marketing NewsLetters
Pets Psychology Religion Parenting
Politics Sales Science Search Engine Optimization
Site Promotion Sports Technology Travel
Web Development Web Hosting WeightLoss Women's Corner
Writing Miscellaneous Articles Real Estate Arts And Crafts
Aging


Disclaimer: The information presented and opinions expressed in the articles are those of the authors
and do not necessarily represent the views of bharatbhasha.com and/or its owners.


Copyright © AwareINDIA. All rights reserved || Privacy Policy || Terms Of Use || Author Guidelines || Free Articles
FAQs Link To Us || Submit An Article || Free Downloads|| Contact Us || Site Map  || Advertise with Us ||
Click here for Special webhosting packages for visitors of this website only!
Vastu Shastra

Unlimited Hosting Provided By AwareIndia







Company IDS